Altivar 312, Variable speed drive ATV312, 0.55kW, 1.4kVA, 46W, 200..240 V, 1 phase supply
Item Number: ATV312H055M2
Specifications
Design
Range of product
Product or component type
Product destination
Warranty
Physical
Supply
- internal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protection
- internal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection
Communication port protocol
- CANopen
- Modbus
Ip degree of protection
- IP20 on upper part without cover plate
- IP21 on connection terminals
- IP31 on upper part
- IP41 on upper part
Protection type
- input phase breaks: drive
- line supply overvoltage and undervoltage safety circuits: drive
- line supply phase loss safety function, for three phases supply: drive
- motor phase breaks: drive
- overcurrent between output phases and earth (on power up only): drive
- overheating protection: drive
- short-circuit between motor phases: drive
- thermal protection: motor
Insulation resistance
Local signalling
- 1 LED (red) for drive voltage
- four 7-segment display units for CANopen bus status
Connector type
Marking
Height
Width
Depth
Net weight
Standards
- IEC 61800-5-1
- IEC 61800-3
Product certifications
- CSA
- UL
- GOST
- DNV
- C-Tick
- NOM
Relative humidity
- 5...95 % without condensation conforming to IEC 60068...2-3
- 5...95 % without dripping water conforming to IEC 60068...2-3
Ambient air temperature for storage
Ambient air temperature for operation
- -10...50 °C without derating (with protective cover on top of the drive)
- -10...60 °C with derating factor (without protective cover on top of the drive)
Eu rohs directive
Mercury free
Rohs exemption information
China rohs regulation
Environmental disclosure
Circularity profile
California proposition 65
Others
Package 1 bare product quantity
Product specific application
Assembly style
Component name
Motor power kw
Motor power hp
[us] rated supply voltage
Supply frequency
Network number of phases
Line current
- 6.8 A at 200 V, Isc = 1 kA
- 5.8 A at 240 V
Emc filter
Apparent power
Maximum transient current
Power dissipation in w
Speed range
Asynchronous motor control profile
- sensorless flux vector control with PWM type motor control signal
- factory set : constant torque
Electrical connection
- Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5-2.5 mm² AWG 14
- L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 2.5-2.5 mm² AWG 14
Option card
- communication card for CANopen daisy chain
- communication card for DeviceNet
- communication card for Fipio
- communication card for Modbus TCP
- communication card for Profibus DP
Supply voltage limits
Prospective line isc
Continuous output current
Output frequency
Nominal switching frequency
Switching frequency
Transient overtorque
Braking torque
- 150 % during 60 s with braking resistor
- 100 % with braking resistor continuously
- 150 % without braking resistor
Regulation loop
Motor slip compensation
- adjustable
- automatic whatever the load
- suppressable
Output voltage
Tightening torque
- Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6: 0.6...0.6 N.m
- L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 0.8...0.8 N.m
Insulation
Analogue input number
Analogue input type
- AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 Ohm
- AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 Ohm
- AI3 configurable current 0...20 mA, impedance: 250 Ohm
Sampling duration
- AI1, AI2, AI3: 8 ms analog
- LI1...LI6: 4 ms discrete
Response time
- AOV, AOC 8 ms for analog
- R1A, R1B, R1C, R2A, R2B 8 ms for discrete
Linearity error
Analogue output number
Analogue output type
- AOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bits
- AOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits
Discrete input logic
- logic input not wired (LI1...LI4), < 13 V (state 1)
- negative logic (source) (LI1...LI6), > 19 V (state 0)
- positive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1)
Discrete output number
Discrete output type
- configurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
- configurable relay logic: (R2A, R2B) NC - 100000 cycles
Minimum switching current
Maximum switching current
- R1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms
- R1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms
- R1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms
- R1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms
Discrete input number
Discrete input type
Acceleration and deceleration ramps
- S, U or customized
- linear adjustable separately from 0.1 to 999.9 s
Braking to standstill
Time constant
Frequency resolution
- analog input: 0.1...100 Hz
- display unit: 0.1 Hz
Physical interface
Transmission frame
Transmission rate
- 10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen
- 4800, 9600 or 19200 bps for Modbus
Number of addresses
- 1...127 for CANopen
- 1...247 for Modbus
Number of drive
- 127 for CANopen
- 31 for Modbus
Operating position
Network frequency
Dielectric strength
- 2040 V DC between earth and power terminals
- 2880 V AC between control and power terminals
Electromagnetic compatibility
- 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
- electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
- electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
- radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
Pollution degree
Protective treatment
Vibration resistance
- 1 gn (f= 13-150 Hz) conforming to EN/IEC 60068-2-6
- 1.5 mm (f= 3-13 Hz) conforming to EN/IEC 60068-2-6
Shock resistance
Operating altitude
- <= 1000 m without derating
- 1000...2000 m with current derating 1 % per 100 m
Unit type of package 1
Number of units in package 1
Package 1 height
Package 1 width
Package 1 length
Package 1 weight
Unit type of package 2
Number of units in package 2
Package 2 height
Package 2 width
Package 2 length
Package 2 weight
Weee
Documents & downloads
hide show-
All
-
CAD Files and Packs
-
Technical Data Catalogues
-
Installation Instruction
-
End of Life Manual
-
Operating Manuals
-
Certificates (MSDS)
-
Declaration of Conformity
-
Software - Data Library
Frequently Asked Questions
hide showPart number for ATV312 Din rail mounting kit
Product Line:
ATV312
Environment:
All
Cause:
Desire to utilize din mounting kit option
Resolution:
The part numbers need to order the mounting kit for this drive are VW3A9804 and VW3A9805.
VW3A9804 covers the following range of drives: ATV312....
018M2, H037M2, H055M2, H075M2, H018M3, H037M3, H055M3, H075M3
VW3A9805 covers the following range of drives: ATV312....
HU11M2, HU15M2, HU11M3, HU15M3, HU22M3, H037N4, H055N4, H075N4, HU11N4, HU15N4, H075S6, HU15S6
Note: The din rail mounting kits are only available for the above drives.
Note: Other drives not list above do not have a din rail kit.
Powering the ATV312 by an external 24Vdc only
Product Line:
Altivar 312
Environment:
All
Cause:
Installation/programming
Resolution:
No, this drive must have line voltage applied. The voltage must be within -15% to +10% of the rated line voltage.